File:Etchasketch.jpg
From WikiProjectMed
Jump to navigation
Jump to search
![File:Etchasketch.jpg](https://upload.wikimedia.org/wikipedia/commons/thumb/f/f4/Etchasketch.jpg/724px-Etchasketch.jpg)
Size of this preview: 724 × 600 pixels. Other resolutions: 290 × 240 pixels | 580 × 480 pixels | 927 × 768 pixels | 1,237 × 1,024 pixels | 1,536 × 1,272 pixels.
Original file (1,536 × 1,272 pixels, file size: 332 KB, MIME type: image/jpeg)
This file is from a shared repository and may be used by other projects. The description on its file description page there is shown below.
![]() |
This image could be re-created using vector graphics as an SVG file. This has several advantages; see Commons:Media for cleanup for more information. If an SVG form of this image is available, please upload it and afterwards replace this template with
{{vector version available|new image name}} .
It is recommended to name the SVG file “Etchasketch.svg”—then the template Vector version available (or Vva) does not need the new image name parameter. |
![]() | This image was uploaded in the JPEG format even though it consists of non-photographic data. This information could be stored more efficiently or accurately in the PNG or SVG format. If possible, please upload a PNG or SVG version of this image without compression artifacts, derived from a non-JPEG source (or with existing artifacts removed). After doing so, please tag the JPEG version with {{Superseded|NewImage.ext}} and remove this tag. This tag should not be applied to photographs or scans. If this image is a diagram or other image suitable for vectorisation, please tag this image with {{Convert to SVG}} instead of {{BadJPEG}}. If not suitable for vectorisation, use {{Convert to PNG}}. For more information, see {{BadJPEG}}. | ![]() |
Summary
DescriptionEtchasketch.jpg |
English: Basic mechanism of operating a 2-dimensional plotter. All of the numbered components correspond to those which move the plotter's stylus horizontally, and the lettered components with those which move it vertically. Device consists of a series of 10 pulleys, 6 cables, 2 rails, and a stylus. Pulley 1 (single-groove) is connected to pulley 2 (triple-groove) via a short infinite reciprocating cable. Two connects to 3 (double-groove) via a longer reciprocating cable which is attached along its upper course to one end of the vertical rail (6), and then a third cable runs from 2 to 3, 4 and 5 (4 and 5 are single-groove) via another much longer loop of cable which attaches between 4 and 5 to the other end of the vertical rail. Likewise, A connects to B, B connects to C and attaches to the horizontal rail (F), and finally B connects to C, D, and E, attaching to F at its other end between D and E. Turning pulley 1 counterclockwise as shown causes 2 to rotate the same way, and this causes all pulleys connected to 2 (3, 4, and 5) to do the same. The rail to which these cables is connected (6, connection points marked in red) will move to the left both at ends, causing the stylus to move in the same direction along the other rail (F). Clockwise movement of pulley 1 has the opposite effect. Pulleys A-E operate the same as 1-5, and act on the horizontal rail (F) to slide the stylus up and down along the vertical one (6). |
Date | |
Source | Own work |
Author | KDS4444 |
Licensing
I, the copyright holder of this work, hereby publish it under the following license:
![w:en:Creative Commons](https://upload.wikimedia.org/wikipedia/commons/thumb/7/79/CC_some_rights_reserved.svg/90px-CC_some_rights_reserved.svg.png)
![attribution](https://upload.wikimedia.org/wikipedia/commons/thumb/1/11/Cc-by_new_white.svg/24px-Cc-by_new_white.svg.png)
![share alike](https://upload.wikimedia.org/wikipedia/commons/thumb/d/df/Cc-sa_white.svg/24px-Cc-sa_white.svg.png)
This file is licensed under the Creative Commons Attribution-Share Alike 4.0 International license.
- You are free:
- to share – to copy, distribute and transmit the work
- to remix – to adapt the work
- Under the following conditions:
- attribution – You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
- share alike – If you remix, transform, or build upon the material, you must distribute your contributions under the same or compatible license as the original.
Captions
Add a one-line explanation of what this file represents
Items portrayed in this file
depicts
26 September 2014
image/jpeg
File history
Click on a date/time to view the file as it appeared at that time.
Date/Time | Thumbnail | Dimensions | User | Comment | |
---|---|---|---|---|---|
current | 18:57, 15 June 2024 | ![]() | 1,536 × 1,272 (332 KB) | commons>Hohum | Cropped to subject |
File usage
There are no pages that use this file.
Metadata
This file contains additional information, probably added from the digital camera or scanner used to create or digitize it.
If the file has been modified from its original state, some details may not fully reflect the modified file.
Orientation | Normal |
---|---|
Horizontal resolution | 100 dpc |
Vertical resolution | 100 dpc |
Software used | GIMP 2.10.38 |
File change date and time | 19:57, 15 June 2024 |
Color space | sRGB |
Unique ID of original document | xmp.did:79E7598B3D46E4118245F95301711106 |
Date and time of digitizing | 21:58, 26 September 2014 |
Retrieved from "https://mdwiki.org/wiki/File:Etchasketch.jpg"